![]() Works with any 1.5Mbps (low speed) or 12Mbps (full speed) USB device. This handy little low-cost USB isolator is exactly what you need to provide protection against harmful noise, ground loops, surges, and spikes. Protect your Designs with Low-Emissions USB 2.Have some USB logic analyzer, multimeter or oscilloscope and bumping up against the frustation of a shared earth ground? The Offspring (known for being electrical engineers) wisely sang "Ya gotta keep'em isolated!" Power and signal isolation improves common-mode voltage, enhances noise rejection, and permits two circuits to operate at different voltage levels. 고속 USB 아이솔레이터의 이퀄라이저 설정을 이용해 채널 손실을 보상합니다Ĭompensate for Channel Loss with Equalizer Settings on High-Speed USB Isolators How to implement an isolated USB 2.0 high speed, Type-C® DRP VDE Certificate for Reinforced Isolation for DIN EN IEC 60747-17 (Rev. UL Certificate of Compliance File E181974 Vol 4 Sec 6 (Rev. TUV Certificate for Isolation Devices (Rev. VDE Certificate for Basic Isolation for DIN EN IEC 60747-17 (Rev. USB Audio Isolation with Isolated USB 2.0 RedriverĬSA Certificate for ISOUSB211xDP (Rev. ISOUSB211DPEVM EU Electromagnetic Compatibility and RoHS DoC (Rev. Implementing an isolated USB2.0 On-the-go (OTG) port ![]() ISOUSB211 High/Full/Low Speed Isolated USB Repeater datasheet (Rev. The device is available in the small foot-print SSOP-28 (28-DP) package. It supports a wide ambient temperature range of –40☌ to +125☌. The ISOUSB211 device is available for reinforced isolation. Used in conjunction with isolated power supplies, the device protects against high voltage, and prevents noise currents from the bus from entering the local ground. This device uses a silicon dioxide (SiO 2) insulation barrier with a withstand voltage of up to 5000 V RMS and a working voltage of 1500 V RMS. The ISOUSB211 has inbuilt programmable equalization to cancel signal loss caused by board traces, which helps in meeting USB2.0 high-speed TX and RX eye-diagram templates. This feature enables the device to support USB On-The-Go (OTG) and Type-C Dual Role Port (DRP) implementations. The device also supports automatic role reversal - if after disconnect, a new connect is detected on the Upstream facing port, then the Upstream and Downstream port definitions are reversed. The device supports automatic connect and speed detection, reflection of pull-ups/pull-downs, and link power management allowing drop-in USB hub, host, peripheral and cable isolation. ISOUSB211 is a galvanically-isolated USB 2.0 compliant repeater supporting low speed (1.5 Mbps), full speed (12 Mbps) and high speed (480 Mbps) signaling rates. 5000-V RMS isolation for 1 minute per UL 1577.Ambient temperature range: –40☌ to +125☌. ![]() ☘ kV IEC 6 contact discharge protection across isolation barrier.Supports automatic role reversal for USB On-The-Go (OTG) and Type-C® Dual Role Port (DRP) designs.Programmable equalization to compensate board trace loss in high speed mode.Supports L1 (sleep) and L2 (suspend) low-power states.Automatic speed and connection detection. ![]() Does not need external crystal or clock input.Supports low speed (1.5 Mbps), full speed (12 Mbps) and high speed (480 Mbps) signaling.parametric-filter Isolated digital inputs.parametric-filter Isolated RS-485 transceivers.parametric-filter Isolated LVDS buffers.parametric-filter Isolated CAN transceivers.parametric-filter Power for signal isolators.parametric-filter Isolated interface ICs.parametric-filter Wireless connectivity.parametric-filter Switches & multiplexers.parametric-filter Microcontrollers (MCUs) & processors.parametric-filter Logic & voltage translation.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |